Prepared so as to add a do-it-yourself water function to your yard panorama? This step-by-step tutorial exhibits you find out how to construct a small DIY waterfall, on a finances of $500 or much less.

You’ll additionally like The right way to Construct a Fireplace Pit Pergola for Swings and The right way to Set up an Above Floor Yard Pool.

how to build your own backyard DIY waterfall

This put up comprises affiliate hyperlinks. Be taught extra and browse our full disclosure coverage right here.

Our Yard DIY Waterfall

Hey Remodelaholics! It’s LZ from The Summery Umbrella, and I’m tremendous pumped to share this wonderful, new DIY put up with you at this time.

This DIY yard waterfall venture began off not as a need, however relatively a necessity. When my husband Mike and I first moved into our house the earlier proprietor had not been in a position to care for the massive yard, after which on high of that nobody had been dwelling in our house for over 6 months.

The pond was a whole mess to say the least! We desperately wanted an aeration system, and rapidly added a pump that was inside our very small finances.

Now, nearly a 12 months later we’re greater than able to design a “prettier” focus and add some tranquility to the world.

Like with all of my tasks I wished to maintain the prices down, but in addition create a gorgeous piece of labor that my household and I may take pleasure in for a lot of, many extra years to come back. As an illustration, do you keep in mind once I created the DIY Potting Bench and even the Mason Jar Pendant Gentle? Very comparable for certain!

With that being mentioned, have you ever ever priced out a pond waterfall package? From my analysis I discovered backyard waterfall kits to vary of $600 – $4,000 (relying on in the event you wanted to rent assist). Undoubtedly out of my finances!

How about flagstone, ledge or slate rock? Jaw dropping, proper? A number of the native shops on the town have been asking a minimal of $60 for one rock at 25 lb. No manner. I’ll do it my manner, thanks very a lot!

In the present day I’m going to indicate you find out how to construct a waterfall on a finances in your individual yard, create your individual rock out of concrete after which “fairly up” the world with discovered rock and vegetation.

We did this multi function lengthy weekend, for LESS than the price of shopping for a primary waterfall package.

Are you prepared? Let’s get began!

DIY Waterfall Tutorial on a Budget

The right way to Construct a DIY Waterfall on a Finances

Supplies & Instruments

Supplies Used:

  • 2x4x8’s (stress handled)
  • 2x6x8’s (stress handled)
  • 1x 6’s (stress handled)
  • 2″ foam insulation
  • 1″ PVC T-fitting (3)
  • 1″ PVC elbow (8)
  • 1″ PVC connectors (6)
  • 1″ PVC pipe 10 foot sections SCH20 (10)
  • 1/6 hp submersible multipurpose water pump
  • wooden screws
  • liquid cement colour
  • concrete combine (we used 6 80lb luggage)
  • concrete mildew
  • mortar (2 40lb luggage)
  • purple primer
  • medium clear pvc cement
  • “discovered” rock

A observe in regards to the pond pump: Since LZ is utilizing a pure pond and the pump is for water aeration, her pump runs repeatedly. For many yard waterfalls, although, you’ll wish to select a pond and waterfall pump and set up an outlet and swap the place you possibly can simply flip the pump off when not in use.

Instruments Steered:

  • drill and bits
  • degree
  • round noticed
  • reciprocating noticed (advantageous tooth blade)
  • pencil
  • screw gun
  • measuring tape
  • framing hammer
  • ruler or something with a straightedge
  • rake
  • wheel barrow
  • shovel

Step 1: Select the Location

First issues first, determine the place to place your waterfall.

Ever since we purchased our house I’ve been majorly crushing on this itty-bitty island proper smack in the course of our heart-shaped pond which is roughly 3/4 of an acre.

It was somewhat consumed with saplings and vegetation so we needed to row our little boat over there to filter an space for the waterfall.

DIY waterfall in a private pond

It could have been an excessive amount of of a trouble to convey all the unneeded branches again over to the “essential land” so the remaining have been burnt instantly on the island.

DIY waterfall in a private pond

No Pond? Create Your Personal Water Supply

LZ’s pond provides the waterfall’s water supply. If you happen to’re constructing in your yard with out a pure water supply, you’ll have to first create your individual water reservoir after which construct the remainder of the waterfall. The simplest manner to do that is to buy a inflexible pond liner that you may get at most house enchancment shops or many gardening/landscaping shops — and naturally, on trusty ol’ Amazon.

Then, at your chosen location, you’ll mark and excavate to suit the pond liner. Degree the liner utilizing sand or gravel beneath as wanted. Fill any gaps across the edges with sand to maintain the liner securely in place.

Alternatively, for a much less structured and extra customized look, you too can use 20 mil black plastic pond liner. Dig the pond, add a 1-2 inch layer of sand on the backside of the opening, and lay out the liner. Safe the liner across the fringe of the pond in a couple of spots, then fold the pond liner to suit the profile of the pool you dug. As you construct the waterfall, you’ll add rocks to carry the pond liner and you’ll trim the surplus as wanted.

Step 2: Make Pond Rocks

Subsequent, it’s time to make some synthetic rocks out of concrete.

Start by mixing your concrete, and coloring it in the event you’d like.

Do you know that they’ve cement colours? I certain didn’t!

make your own rocks from concrete for a DIY waterfall feature

Be certain that to learn and observe the instructions on the cement colour bottles first. I do imagine we did it the incorrect manner the primary time round. Oops!

make your own rocks from concrete for a DIY waterfall feature

After your cement and colour is completely combined, positioned it inside the mildew, clean it over (we used a chunk of wooden we had available) after which instantly take away the mildew.

NOTE: Use a tarp when carrying out this step. This manner your new rocks is not going to stick, and shall be simple to take away once they have accomplished dried.

how to make your own rocks from concrete for a DIY waterfall feature

I used to be somewhat nervous to right away take away the mildew, however our first one (after which each one after) labored out simply advantageous!

how to use a paver mold to make your own rocks from concrete for a DIY waterfall feature

We ended up utilizing three bottles of cement colour (every with their very own bag of cement), after which an extra two extra luggage of concrete with their common colour with out a mildew. They have been created by simply making massive square-like sections on the tarp to resemble flagstone or slate.

Additionally, simply keep in mind these little guys take a very long time to completely dry. They are going to be extraordinarily fragile for the primary 24 hours.

how to make your own rocks from concrete for a DIY waterfall feature

Step 3: Create The Waterfall Fountain

To make the water circulate and “fall” out of the rock as a substitute of shoot out on the high of the waterfall, we divided the availability line 4 methods with some 1″ T-fittings and 1″ elbows. We pre-cut 2″ lengthy items of 1″ PVC to attach all of the fittings (male connectors).

building a custom DIY waterfall fountain from PVC in a pond
building a custom DIY waterfall fountain head for a backyard pond

After priming all of the items to be related we began with one T-fitting and two male connectors, then added two extra T-fittings to that.  From these two T-fittings 4 extra male connectors have been used to  add the the 4, 90 diploma elbows.

building a custom DIY waterfall fountain head from PVC pipe in a pond

As you possibly can see within the beneath image this shall be your finish end result. Don’t fear, this is not going to be seen! That is simply merely the fountain head that shall be underwater.

building a custom DIY waterfall fountain head from PVC pipe for a backyard pond

Step 4: Body the Waterfall Construction

Subsequent, assemble the framework. For our lengthy cascading waterfall, we constructed three staggered containers that measured 24″ by 36″. For small areas, you’ll seemingly wish to stack the containers to construct a taller waterfall and create the body (and stack the rocks later) in accordance together with your area.

The primary field was constituted of 2X6’s and the opposite two from 2X4’s. For additional sturdiness, use stress handled lumber or redwood — however since this body shall be coated with concrete, we simply used common building grade lumber.

A very powerful step right here is to verify the wooden frames are degree (to keep away from water working over the edges). We screwed them to one another with 3″ screws.

building a custom DIY waterfall in a pond -- the wood frame to support the waterfall

The place the final field hung off the sting we used some minimize 2X4’s to brace it up and maintain it degree (see image beneath).

building a custom DIY waterfall in a pond - build the cascading waterfall frame from lumber

Step 5: Configure Water Provide Strains

Quickly place your fountain head inside the highest of your waterfall construction to see the place your provide traces should be run.

For a taller and extra compact waterfall, you’ll seemingly have to run some further tubing or copper pipe to put the fountain head the place you need it. You too can use a sturdy container, like a flower pot, to assist maintain the construction and defend the tubing, if wanted.

building a custom DIY waterfall for a backyard pond - cascading waterfall frame structure with homemade PVC pipe fountain head

Step 6: Minimize Foam Insulation to Match Body

Subsequent, minimize and match the two″ foam insulation to slot in the containers.

use foam, pvc, lumber, and concrete to make a DIY waterfall feature on a budget

Step 7: Set up Fountain Head Extensions

Minimize and join some 12″ PVC extensions to come back up by means of the froth.

Once we pressed the froth to the highest of the fountain head, it left an impression which enabled us to chop holes for the pipe to protrude from. Once more hold calm, this can all be hidden later.

use foam, pvc, lumber, and concrete to make a DIY waterfall feature on a budget

Step 8: Set up Foam Set up in Body

Set up 1×2 helps for the froth sheets. You may additionally use rebar right here in case your waterfall construction is taller.

use insulation foam, pvc pipe, lumber, and concrete to make a DIY waterfall feature on a budget

Safe the froth into place with some screws. Don’t drive the screws throughout, simply sufficient to carry the froth in place.

how to make a budget friendly cheap backyard waterfall - use foam, pvc, lumber, and concrete to make a DIY waterfall feature

Step 9: Set up Waterfall Edge

Use some 1X4’s to create a “lip” round your containers (see subsequent two photos for examples).

how to build a DIY waterfall for a backyard garden
how to build a DIY backyard garden waterfall

Have you ever been questioning how all these photographs have been taken? I believed you’d get a kick out this image! Let me simply begin off by saying that I’ve been recognized to be somewhat clumsy. Rowing this little boat across the island whereas taking photos (a few of them I used to be standing up in!) was fairly amusing. Nevertheless, I can proudly say that I didn’t fall in all through your entire period of this venture!

how to build a DIY waterfall

 Step 10: Join Water Provide

Join your water provide line to the fountain head and bury it as vital. Fill a few of the voids with leftover foam and people do-it-yourself “rocks”. Our water provide line is on the far proper aspect of the beneath image.

how to build a DIY waterfall using insulation foam and lumber and concrete

Step 11: Skim Coat the Waterfall Body with Concrete

Combine your closing bag of concrete and apply liberally to all of the containers ensuring it fills in all of the little gaps and cracks.

Additionally, make sure that it’s roughly 1″ thick in all areas, after which slope it as much as the lip with a scrap piece of wooden (or your palms, in the event you dare!). This creates a pleasant trough for the water to fill in and run out. Nevertheless, waterfalls aren’t troughs so we added some extra of our do-it-yourself “rocks” to interrupt it up. Do that whereas your concrete continues to be moist to make sure they adhere.

NOTE: Our do-it-yourself rocks had a gorgeous colour once they have been first made, however as they hardened their colour pale considerably.

how to build a concrete DIY waterfall for a backyard pond or garden

Listed below are a couple of completely different angles simply to present you an concept how ours checked out this step.

concrete DIY waterfall step by step tutorial
how to build a DIY waterfall on a budget using concrete and insulation foam

Step 11: Add Extra Rocks

Combine the mortar and apply to the outer sides of the construction, and place your “rocks” into the mortar to interrupt up the perimeters and make it look extra pure.

how to build a DIY waterfall on a budget using concrete cement

Step 12: Let The Concrete Dry

Permit loads of time for concrete to completely dry and harden. I extremely suggest a minimal of 24 hours and 48 hours is fairly commonplace for producers to suggest. The longer, the higher! (The concrete will take a number of weeks to totally remedy, however you possibly can work with it as soon as it’s dried 24-28 hours.)

Step 13: Trim PVC Fountain Head Extensions

After the whole lot has completely dried , it’s now time to hook up the water pump and try it out!

BUT FIRST: Previous to turning in your water pump for a check drive, make sure that your concrete has certainly hardened, after which go forward and trim off these PVC extensions roughly 1/4″ above the concrete. We used the reciprocating noticed to do that (previous to turning on the water), after which tried it out!

make your own DIY waterfall on a budget

Step 14: Join The Water Provide & Take a look at

Join your water pump. Be certain that to observe the directions in your water pump since each is somewhat bit completely different. If you happen to’re not working with a pond like ours, now’s the time to fill your pond liner with water.

Since we already had the pump in place we simply needed to join our PVC pipes from the island to its location.

how to build a DIY waterfall

As you possibly can see on this beneath image the gap is somewhat little bit of a hike and required lots of PVC. A small yard set up would require only a size of tubing to get from the water to the pump.

DIY Waterfall on a Budget

I let Mike leap within the pond and connect our PVC to our water pump. I’ll be sincere! There was completely no manner that I used to be stepping into that pond. I’ve seen water snakes and snapping turtles in it earlier than, and I’m fairly alright watching from dry land!

diy waterfall and pump

I like it when a plan comes collectively!

make your own concrete DIY waterfall on a budget

Step 15: Add Extra Rocks

Final, however not least, we gathered up some “discovered rock” and place them round round our new waterfall.

Now actually, this step will all rely in your location. I grew up within the Midwest round lots of farms (and even now in North Carolina), and I’ve at all times been in a position to simply discover rock round these fields.

use rocks to make your own DIY waterfall on a budget

I’m certainly not encouraging you to enter onto any farm or discipline that you just want. Nevertheless, Mike and I’ve fairly a couple of mates who personal farmland who’ve lovely rock that they only can’t do away with fast sufficient!

What I’m encouraging although is that you just ask your individual household and mates (or possibly even a neighbor) in the event that they need assistance eliminating these “hindrances”. To this point, I’ve by no means been advised no.

 There’s actually no good manner so as to add rock. Simply begin off by testing them out. Place them throughout your waterfall on each the within and round it.

on a budget, DIY waterfall for $300 - step by step tutorial at Remodelaholic

Add a couple of flowers and mulch, and voila you’ve created your individual little oasis! To not point out, if there is part of your construction that isn’t as interesting to you (for no matter cause) simply add your discovered rocks, mulch and vegetation shut by to cowl it up.

how to build your own DIY waterfall for a backyard pond or garden

In case your pond is self-circulating, you’ll want to make sure the water degree stays stuffed and also you’ll flip it off once you’re not utilizing it.

diy pond waterfall on a budget

As a result of ours is required to aerate the pond water to maintain it cleaner, our waterfall is designed to remain working on a regular basis, and clearly we by no means have to refill the water reservoir!

DIY Waterfall Tutorial on a Budget
cheap diy waterfall for a backyard garden pond

 I’d have liked to get extra photos from a distance, however sadly it was so arduous to see something!

diy pond waterfall
Creating a custom water feature can be pricy! Follow this DIY tutorial for how to build a waterfall on a budget, including creating your own rock out of concrete.

How A lot Does It Price To Make a Waterfall?

This venture will finally rely in your finances.  We had a really small finances so we needed to get fairly artistic with the intention to make this work. This specific venture took us all weekend (plus a Friday night time), however that was primarily because of the concrete. I actually don’t suppose you would do it much less time as a result of it’s a must to await the whole lot to dry, however not less than you received’t be out within the solar all day!

  • wooden: $40
  • foam insulation: $38
  • PVC: $40
  • screws: $6
  • cement colour: $15
  • purple primer & pvc cement: $7
  • concrete combine: $24
  • concrete mildew: $15
  • mortar (2: 40 lb luggage): $8
  • water pump: $64
  • lilies: $36
  • 3 luggage of mulch: $10
  • discovered rock: $0
  • complete: $303

I hope you loved studying this tutorial and joyful constructing!

—————————————-

Make your yard even MORE wonderful with these tasks, too:

  • 2x4x8’s stress handled
  • 2x6x8’s stress handled
  • 1x 6’s stress handled
  • 2″ foam insulation
  • 1″ PVC T-fitting 3
  • 1″ PVC elbow 8
  • 1″ PVC connectors 6
  • 1″ PVC pipe 10 foot sections SCH20 10
  • 1/6 hp submersible multipurpose water pump
  • wooden screws
  • liquid cement colour
  • concrete combine we used 6 80lb luggage
  • concrete mildew
  • mortar 2 40lb luggage
  • purple primer
  • medium clear pvc cement
  • “discovered” rock

Step 1: Select the Location (Create Your Pond)

  • LZ’s pond provides the waterfall’s water supply. If you happen to’re constructing in your yard with out a pure water supply, you’ll have to first create your individual water reservoir after which construct the remainder of the waterfall. The simplest manner to do that is to buy a inflexible pond liner that you may get at most house enchancment shops or many gardening/landscaping shops — and naturally, on trusty ol’ Amazon.

  • Then, at your chosen location, you’ll mark and excavate to suit the pond liner. Degree the liner utilizing sand or gravel beneath as wanted. Fill any gaps across the edges with sand to maintain the liner securely in place.

  • Alternatively, for a much less structured and extra customized look, you too can use 20 mil black plastic pond liner. Dig the pond, add a 1-2 inch layer of sand on the backside of the opening, and lay out the liner. Safe the liner across the fringe of the pond in a couple of spots, then fold the pond liner to suit the profile of the pool you dug. As you construct the waterfall, you’ll add rocks to carry the pond liner and you’ll trim the surplus as wanted.

Step 2: Make Pond Rocks

  • Start by mixing your concrete, and coloring it in the event you’d like.

  • Be certain that to learn and observe the instructions on the cement colour bottles first.

  • After your cement and colour is completely combined, positioned it inside the mildew, clean it over (we used a chunk of wooden we had available) after which instantly take away the mildew.

  • NOTE: Use a tarp when carrying out this step. This manner your new rocks is not going to stick, and shall be simple to take away once they have fully dried.

  • We ended up utilizing three bottles of cement colour (every with their very own bag of cement), after which an extra two extra luggage of concrete with their common colour with out a mildew. They have been created by simply making massive square-like sections on the tarp to resemble flagstone or slate.

  • Additionally, simply keep in mind these little guys take a very long time to completely dry. They are going to be extraordinarily fragile for the primary 24 hours.

Step 3: Create The Waterfall Fountain

  • To make the water circulate and “fall” out of the rock as a substitute of shoot out on the high of the waterfall, we divided the availability line 4 methods with some 1″ T-fittings and 1″ elbows. We pre-cut 2″ lengthy items of 1″ PVC to attach all of the fittings (male connectors).

  • After priming all of the items to be related we began with one T-fitting and two male connectors, then added two extra T-fittings to that. From these two T-fittings 4 extra male connectors have been used to add the the 4, 90 diploma elbows.

  • As you possibly can see within the image this shall be your finish end result. Don’t fear, this is not going to be seen! That is simply merely the fountain head that shall be underwater.

Step 4: Body the Waterfall Construction

  • Subsequent, assemble the framework. For our lengthy cascading waterfall, we constructed three staggered containers that measured 24″ by 36″. For small areas, you’ll seemingly wish to stack the containers to construct a taller waterfall and create the body (and stack the rocks later) in accordance together with your area.

  • The primary field was constituted of 2X6’s and the opposite two from 2X4’s. For additional sturdiness, use stress handled lumber or redwood — however since this body shall be coated with concrete, we simply used common building grade lumber.

  • A very powerful step right here is to verify the wooden frames are degree (to keep away from water working over the edges). We screwed them to one another with 3″ screws.

  • The place the final field hung off the sting we used some minimize 2X4’s to brace it up and maintain it degree (see image beneath).

Step 5: Configure Water Provide Strains

  • Quickly place your fountain head inside the highest of your waterfall construction to see the place your provide traces should be run.

  • For a taller and extra compact waterfall, you’ll seemingly have to run some further tubing or copper pipe to put the fountain head the place you need it. You too can use a sturdy container, like a flower pot, to assist maintain the construction and defend the tubing, if wanted.

Step 6: Minimize Foam Insulation to Match Body

Step 7: Set up Fountain Head Extensions

  • Minimize and join some 12″ PVC extensions to come back up by means of the froth.

  • Once we pressed the froth to the highest of the fountain head, it left an impression which enabled us to chop holes for the pipe to protrude from. Once more hold calm, this can all be hidden later.

Step 8: Set up Foam Set up in Body

  • Set up 1×2 helps for the froth sheets. You may additionally use rebar right here in case your waterfall construction is taller.

  • Safe the froth into place with some screws. Don’t drive the screws throughout, simply sufficient to carry the froth in place.

Step 9: Set up Waterfall Edge

Step 10: Join Water Provide

Step 11: Skim Coat the Waterfall Body with Concrete

  • Combine your closing bag of concrete and apply liberally to all of the containers ensuring it fills in all of the little gaps and cracks.

  • Additionally, make sure that it’s roughly 1″ thick in all areas, after which slope it as much as the lip with a scrap piece of wooden (or your palms, in the event you dare!). This creates a pleasant trough for the water to fill in and run out. Nevertheless, waterfalls aren’t troughs so we added some extra of our do-it-yourself “rocks” to interrupt it up. Do that whereas your concrete continues to be moist to make sure they adhere.

Step 13: Let The Concrete Dry

  • Permit loads of time for concrete to completely dry and harden. I extremely suggest a minimal of 24 hours and 48 hours is fairly commonplace for producers to suggest. The longer, the higher! (The concrete will take a number of weeks to totally remedy, however you possibly can work with it as soon as it’s dried 24-28 hours.)

Step 14: Trim PVC Fountain Head Extensions

  • After the whole lot has completely dried , it’s now time to hook up the water pump and try it out!

  • BUT FIRST: Previous to turning in your water pump for a check drive, make sure that your concrete has certainly hardened, after which go forward and trim off these PVC extensions roughly 1/4″ above the concrete. We used the reciprocating noticed to do that (previous to turning on the water), after which tried it out!

Step 15: Join The Water Provide & Take a look at

  • Join your water pump. Be certain that to observe the directions in your water pump since each is somewhat bit completely different. If you happen to’re not working with a pond like ours, now’s the time to fill your pond liner with water.

  • Since we already had the pump in place we simply needed to join our PVC pipes from the island to its location.

  • The space for our pond is somewhat little bit of a hike and required lots of PVC. A small yard set up would require only a size of tubing to get from the water to the pump.

Step 16: Add Extra Rocks & Flowers

  • Final, however not least, we gathered up some “discovered rock” and positioned them round our new waterfall.

  • Ask your individual household and mates (or possibly even a neighbor) in the event that they need assistance eliminating these rock “hindrances”. To this point, I’ve by no means been advised no.

  • There’s actually no good manner so as to add rock. Simply begin off by testing them out. Place them throughout your waterfall on each the within and round it.

  • Add a couple of flowers and mulch, and voila you’ve created your individual little oasis! To not point out, if there is part of your construction that isn’t as interesting to you (for no matter cause) simply add your discovered rocks, mulch and vegetation shut by to cowl it up.

A observe in regards to the pond pump: Since LZ is utilizing a pure pond and the pump is for water aeration, her pump runs repeatedly. For many yard waterfalls, although, you’ll wish to select a pond and waterfall pump and set up an outlet and swap the place you possibly can simply flip the pump off when not in use.
In case your pond is self-circulating, you’ll want to make sure the water degree stays stuffed and also you’ll flip it off once you’re not utilizing it. As a result of LZ’s is required to aerate the pond water to maintain it cleaner, the waterfall is designed to remain working on a regular basis, and clearly they by no means have to refill the water reservoir!
How to build a DIY waterfall on a budget (as in, $300!)

First revealed 15 June 2015 // Final up to date 03 Could 2023

Source link

By admin